sjaume

About

Username
sjaume
Joined
Visits
0
Last Active
Roles
Registered User

Comments

  • Hi and thank's for your answer : - merge : I thouht that it was a real htp/ltp merger but not simply an input selector. ( but i explained that in an another post ) - touch problem : i started a new show today and i didn't have yet the same b…
  • hi chrisf Ok for the engine effect...we'll wait about the merge : It is powerfull to have the possibility to merge input (htp or ltp) in the following cases with a mediaserver: - to control jarag ( mediaserver pixel mapping) & consol…
  • Hi chris Actually, after a full shutdown in software i have to wait few second to to switch off/on. But during console operation, if i switch off then of, the console restarts immediately. It's all right, thank's for your answer I'l…
  • Michael_Graham wrote: » Sebastien If you did the full tech note your desk should boot without having to wait 5 seconds. Did you cut the reset switch wire? I would re-do the tech note making sure you do every step. If you still have the same …
  • Hi, I made the complete procedure on one of our FB4, but it's doesn't not work. I have to wait more than 5s after having switch off the console to see it turning on after switch on. Serial number : 5508412100098 Best regards SEBASTIEN
  • Hello I can give you my own experience with hippotizer. I use them in 3.1 SP 1 software version . On Hippotizer i patch : - 1 or 2 master 3.1 ( depends of the hippotizer model ) - X layer 3.0.14 - Keystones layer ( i build it in person…
  • oups !! i've found the information on the HES web site. We need the special DVI to vga converter.
  • ok thank's best regards
  • hi lainer, i'm waiting my fullboar 4. please, can you send me photo and dimensions of the flight case. Thank's best regards Sébastien
  • Hi steph & gael , i'd seen too that the rate shell is yet implemented on the midi chart tab. But It's implemented on two midi note : rate + and rate -. So, control that by midi, needs to two physical midi controllers. For example : 1 fader for …
  • Do you have the Fullboar 4 case dimensions ? Thank's Sebastien
  • Hi every bobby, I would like to know if some have information about the HOG4 software development. Do you know if, like Hog 3 family, all the next release ( V2, V3 ...) will be desalinated to all the desk ( Hog4; fullboar4, rpadhog 4 ....) . …
  • The keyboard really send note off........(not a note on with velocity at 0 ) I think that Sander is on the goog way to find this bug..... Because i've tried to control the RHFB with LOGIC ( cubasis ), and i have the same results ( the note off m…
  • So i'm really really surprised of your answer.... I used yesterday, this keyboard "ax7" the run cues.......and it is sure when i release a key, i run a cue. I can't modify the note off velocity, but you know that, because it's a fixed value ( …
  • i have allaready tried that. i have got a full boar + fader wing, and last week, the screen of the fader wing became pink at the end of the show
  • HI, one of touchscreen of my RHFB, has sometimes a pink coloration ...... I have invert the touch screen connection inside..and the problem appears on the other screen.......so it's not a touch screen problem To disconnect and reconnect the…
  • hi foxrider, can you analyse your midi note off message ? to know if the velocity note off data is at 0 or 64 or else.
  • A note off is always send by a midi keyboard when you depress a key ...press : note on.......depress : note off But all the keyboards don't use the same value for the note Off. The problem is the Velocity note off value.......and in my ca…
  • I forgot : My system is a ROADHOG FULL BOAR + RH PB Wing + AX7 keyboard
  • Hi sander, i have tested your configuration: with ITM matrix on iphone, etc.........actually it works perfectly as you said. So Itm matrix send a note off, but the last data value is different than a real keyboard. In fact : Itm matrix for …
  • are you sure.....i have tested the system yesterday, with an Roland AX 7 keyboard....I is sure : the "note off" commands as the same action as the "note on" command
  • Ok That's great......I can wait few weeks......so i'm impatient to discover he new release. Have you got more information about The 3.1.7 release ??
  • hi Thank's for your replie, It's exactly what i need Best regards SEBASTIEN
  • I had the same bug, few months ago. Reinstall XPe image and clear all files. A virus is certainly the cause.
    in Road Hog Comment by sjaume June 2010
  • To stop Fx position in the next cue ( cue 2 in your example ) : open the cue 2 editor...click on "table"......click & set off in the Pan & tilt zone......instead of "track" seb
    in FX stoping Comment by sjaume June 2010