theDutchGuy

About

Username
theDutchGuy
Joined
Visits
0
Last Active
Roles
Registered User

Comments

  • I assume you're referring to a big blast that then slowly fades out...? Rather than messing with effects, I find it quicker and easier to make a two-step cuelist (step one: dimmer and rate @ full in 00 seconds, step two: dimmer fade to 0% in 2 seco…
  • SfeerPeer wrote: » @Erik: - full boar in 013 uses XPe 1.0.4 and Hog 3.0.1. instead of XPe 1.4.0. / Hog 3.0.5 I've had some annoying issues as well in 3.0.1. thru 3.0.3, but lots of bugs wil be gone when Paul finally will update the desk. th…
  • wrote: When i record a new palette (many parameters or emty) the playback is jumping for short time, when the activ cue for example Pan Tilt is created with effects engine. No different it`s a focus color or beam palette. This sounds a lot …
  • jxgriffi wrote: » Wow...and I thought I was going to be bad... Here's the one I thought about posting.... "Now that Hog3PC is Vista compatible, I tried loading it into a T2, but can't get it to recognize the pen. What am I doing wrong?" Wel…
  • A 250mm pitch Colorweb PSU controls 10 sections of web (16 LED units per section at 3 channels (RGB) each) thereby using 480 DMX-channels. the PSU requires power and DMX-in, and that's it. there is no DMX-thru connector. I don't know the 125 mm p…
  • you can get great results out of a low-res pixel grid like the Colorweb if you make smart use of the effects engine, and think thoroughly about the groups you set up before you start programming. my best advise is to reserve some time to plan, and t…
  • an older thread resurrected...?!? Is Craig still looking for people...?
  • lyjwow26 wrote: ...Spam Removed... ...wow, is it me, or has this topic derailed all of a sudden...?
  • Marty, I'd have to disagree with you saying: " It was no "big secret" that the Full Boar was being worked on and would be released shortly after the RH.....you can't blame someone else if you didn't do your homework properly. " It may not h…
  • as an aside, Technobeams should strike automatically if they're powered up and receiving DMX. disconnecting an reconnecting the fixture should have it striking quick. maybe that's possible without having to lower the electric....?
  • i think the most common way of handling this kind of situation would be to patch all dimmers as separate deskchannels so you have individual control over them, and then use "groups" to select several deskchannels/ dimmers at the same time. lots of …
  • ...and apparently it has been, Joe. and now all my responses seem to go nowhere... anyway, case closed...
  • oh, real snappy comeback, there. be sure to enlighten us with more of your wisdom...
  • Marty, that comment was in regards to the DP8000 not making the Hog RDM enabled, which was kind of what the original question was about. and I did say it wasn't going to answer everyone's EVERY prayer. As good, I'm sure, as the DP8k is gonna be, …
  • anyone correct me when I'm talking out of my ass, guys...? I'm mostly self-taught, myself... :rolleyes: ArtNet is an open source protocol -developed by Artistic License- that allows you to send DMX-signal over an Ethernet-network. obvious advanta…
  • Nibor, you should take a page out of Josh/ Electric Mayhem's book, and write replies like him: an articulate, reasoned explanation of his opinion, with suggestions of what he feels could or should be the next step for the Hog platform. To boot, h…
  • cheers Frank, you've got mail... consider this thread closed already, guys...
  • I do this all the time, and my workaround is as follows: make your stack of rotating gobo´s, (set `cue only` to `off`) , and include the value "rotate 0%" in the first step. this keeps the gobo stack in rotation mode throughout. then make your r…
  • this might be the worst suggestion in the history of stupid suggestions, but... is the grand master up?
  • how similar need the showfiles be? same patch? more same stuff...? is it just a matter of copy/paste? cheers, Erik