Aruvin

About

Username
Aruvin
Joined
Visits
0
Last Active
Roles
Registered User

Comments

  • MLorenz wrote: » Which Software version are you on? Fullboar 4 Version 2.2.0 on all.
  • Hi All, Problem solve after changing bios setting. Thx..:trink26:
  • Mitch wrote: » Do both consoles have the same software version? It is necessary for them to connect. Yes..both had same version.
  • Andre wrote: » Just to review your settings: Main console: DHCP OFF IP: 172.31.0.1 Sub: 255.255.0.0 Console server ON Port 6600 Internal DP ON Console ID 1 Client console: DHCP OFF IP: 172.31.0.2 Sub: 255.255.0.0 Console server OFF …
  • Andre wrote: » Are they both running the same port number 6600? Your main console is running the server and the client not? Yes, both running 6600. Main running server and client not. Am I missing sth here? The example attach is not meant for …
  • Aruvin wrote: » I am running manual network. Main server as 1 and client 2.
  • Andre wrote: » Hello Aruvin, please tell us more about your network and console settings. IP adresses, console ID's, etc. Thanks I am running manual network. Main server as 1 and client 2.
  • Hi, I had the same problem with 02 of my roadhog fullboar. Had done clean install and running the latest updates. I was just doing a led color chs when it happen. Sometime it just crash when I did nth.. This problem is gona kill me 1 day..
  • HI All, problem solved..Subnet must be set to 255.0.0.0 on dhcp router to use with MA.. Thx:notworthy:
  • Hi Paul, Yes it work with my roadhog fullboar. Will try to figure out the MA setting and try to change the router subnet. Thx.:headbang:
  • My setup is simple. GrandMA to a switcher via cat5, link to a dhcp router and 04x DML with built-in axon.
  • Hi Paul, No, I can't change the subnet on my router. I am following the steps on ur support page for GrandMA config on DML with built-in axon.
  • Also, if I select artnet, instead of dhcp on the DML, I can control the pan tilt on the MA..
  • Hi Paul, Yes, I am using a dhcp router set to 2.0.0.1 and a external axon as CMA. Artnet and universe is set. The DML set to DHCP and it reads 2.0.0.101 and subnet 255.255.255.0. my roadhog works fine with this setting. So, is the subnet address…
  • Hi Matt, Thx. Yes, the harddisk cable is not plug in...:friday:
  • Hi Abbe, thx for the pointer. will try to swop the fan unit and see if it works. I got another unit giving out error msg as per the attach when i select MP input. What should I do about it. Thx alot. Alvin
  • HI Abbe, my mistake, 1st batch(or not) but had upgrade to the axon server now. Got the media working with my console. My bad for not using a DHCP router+Switcher, I just go direct to a swticher, thats why its not communicating... After tesing, …
    in patchDML Comment by Aruvin July 2011
  • Hi Abbe, I am frm Singapore. Yes, it's the first batch. Ok, maybe I am missing something, the switch is nt a dhcp router.. will change it and try again. Getting all confuse with artnet and ip address... Thx Alvin
    in patchDML Comment by Aruvin July 2011
  • Hi Abbe, ok, I followed your steps in the quick start. I had my RoadHog, Laptop running CMA, and mediawing running the PT all cat5 into a switch. when I select DHCP on the DML network, all values become 0.. I am getting abit confuse here, s…
    in patchDML Comment by Aruvin July 2011
  • Zach Peletz wrote: » Aruvin, send me an email and I'll get you those documents. Ok, thx.. Had send u an email.
  • ok, able to update some of the firmware after on/off. except for fiber link RX. tried updating again direct from my laptop toolset to the DML with "FRMT" error but still the same..will check with eddie on that. Btw, is the "FRMT" error the cause…
  • Hi, the pictures were taken after the upgrade. Not sure wat u mean by artnet plug-in or how to remove artnet from the fixture.. Basically, I had all 08 units running cat5 cables to a hub and then to another hub which splits to my MA Console and M…
  • ok, I had done the update for the EC and EMP using the toolset version 1.4 build 16. The EC now reads DV10 update v1.1.9 and the EMP reads v1.0.33. Able to change the universe now but another bigger problem occurs! I gt 02 units with "frmt" er…
  • Zach Peletz wrote: Ok. The current release has been updated to 1.1.9. Please follow this link and update your fixtures to the latest software and then let me know if you're still having a problem.
  • Zach Peletz wrote: What version software package is on your DMLs? 1.1.8 is the latest release. What DMX universe are you trying to set them to? One thing to try is to unplug ArtNet and/or DMX then try setting the universe. See if that works, in th…
  • Zach Peletz wrote: Aruvin, What version of software is on your DMLs and do the ones that aren't responding have the same version as the one that is? Are you making this setting in the menu of the DML? I had check the version.. not all the sa…
  • oh, sorry abt that.. yesh, i am using the fixture builder and trying to build a LED fixture patch from new.. Both screen went black half way thru when i am playing with the fixture builder..and I have to power off and on it again. When i final…
  • amir877 wrote: Look like you don't burn it as an ISO image. Thx..had tried to burn it again and it works! Problem solved after doing the clean install... Cheers.:friday:
  • amir877 wrote: Look like you don't burn it as an ISO image. Hi, was following the step frm the link using the nero burner... anyway, will try again.. thx
  • ericthegeek wrote: Install 2.3.1 from an ISO, then upgrade to 2.3.2. The HogIII ISO for 2.3.2 was withdrawn due to a boot issue that occurs on some consoles. I know it's scary to have your console not boot but there's nothing to worry about. Th…
  • Btw, could a faulty batt cause the problem? Is there suppose to be lite on the batt led indicator when we power up the console? Thx
  • barnes2000 wrote: Are you running v2.3.2? There was a bug in the upgrade of that version that causes stalls in the booting of the console. You should email support and let them know. Hi, was trying to update to v2.3.1. frm previous version u…
  • teerickson wrote: Aruvin, We did some work with our window manager on Hog 3PC that included adding a Hog2-style Split Window button. We're currently working on porting these changes to the Wholehog 3 console and you should see the Split Window …
  • teerickson wrote: Aruvin, We are currently working on Wholehog 3 software v2.0. This software will allow communication between the Wholehog 3 console, the Hog iPC, and Hog 3PC and will allow Hog 3PC products to communicate directly with DMX Pro…